Rigid liners
Straight flues can take rigid stainless pipe which suits wood burning appliances well.
A Tamaqua chimney sweep can reline your chimney with a liner sized to the appliance and insulated where the system calls for it. Call (272) 291-2023 to reach a local chimney sweep.
A chimney liner is the channel inside the chimney that carries smoke and combustion gases up and out. Without one, heat and acidic condensation attack the masonry, and gaps can let heat or carbon monoxide escape into the home. In older houses, it is common to find an unlined chimney or a clay tile liner that has failed.
Relining usually comes up for one of a handful of reasons. Damaged clay tiles, missing mortar between tiles or no liner at all are the most common triggers. Installing an insert, stove or high efficiency furnace often means the old flue is the wrong size.
Before relining, the chimney should get a thorough inspection, usually a Level 2 inspection with a camera run up the flue. That reveals whether the existing tiles can be repaired or need to be replaced, and it shows the route a new liner will take. You can ask the sweep to walk you through the video.
If the problem goes deeper than it first looked, a Tamaqua chimney sweep may also recommend chimney liner repair or chimney inspection.
Looking for Tamaqua chimney liner installation? Call (272) 291-2023 to talk to a local chimney sweep.
Call nowRelining a chimney is a careful job that starts well before the liner goes in.
The sweep inspects the flue from top to bottom, usually with a video camera. It decides between repair and relining.
The liner diameter is matched to the appliance outlet or the fireplace opening, following the manufacturer guidance. The full height of the flue is measured too.
The flue is swept and any loose tile or obstruction is cleared so the liner can pass. Tight flues sometimes need old tiles removed.
The stainless liner is lowered from the roof down to the appliance, often wrapped in an insulation blanket. Many liner systems are tested with insulation for clearance to combustibles.
At the top, a plate and cap close off the flue, and at the bottom the liner connects to the appliance. The connections keep gases from leaking into the old flue.
The appliance is fired or the draft is tested to confirm smoke and gases go up and out. Keep carbon monoxide alarms on every level of the home.
Straight flues can take rigid stainless pipe which suits wood burning appliances well.
Flexible stainless steel liners bend around offsets in the chimney and are common for inserts, stoves and gas appliances.
Liners sized for gas and oil appliances to keep combustion gases moving out of the house.
Insulation is wrapped around the liner or poured into the space around it to keep flue gases warm and meet clearance requirements.
A cement based mix is poured around a form inside the chimney to create a smooth new flue in a single solid lining.
Most relining jobs use stainless steel, which handles high heat and corrosive flue gases well. Flexible stainless goes around offsets in a chimney, and rigid stainless suits straight runs. Liners are sold as tested systems, with grades suited to wood, gas or oil.
Insulation around the liner helps flue gases rise and keeps the outside of the chimney cooler. A cap and top plate finish the job at the top of the chimney. In Tamaqua, a stainless liner is a common upgrade when installing an insert or wood stove.
Relining means putting a new liner into a chimney that has an old, damaged or missing one. It is often recommended after a chimney fire, when clay tiles crack, or when a new appliance needs a different flue size. Most chimneys can be relined from the roof without opening walls.
When you call (272) 291-2023, tell the sweep what vents into the chimney, such as a fireplace, stove, furnace or water heater. A furnace replaced with a high efficiency model that vents through the wall can leave the water heater alone in an oversized flue, which leads to poor draft and condensation. A smaller liner brings the draft back where it should be.
In Tamaqua, older homes often have unlined chimneys or clay tiles that have cracked with age. From Tamaqua out to places nearby like Coaldale, Lansford, Summit Hill and Nesquehoning, wood stoves and inserts are common, and each one needs a properly sized liner, so it is worth having the flue inspected before the next heating season.
Searching for chimney liner installation near me from Tamaqua or Coaldale, Lansford, Summit Hill and Nesquehoning? Call (272) 291-2023 to talk to a chimney sweep who works in your part of town.
Winters here are long and cold, and the heating season usually runs from October well into April. The hardest thing on brick here is not the cold itself but the constant swing above and below freezing: water soaks into brick, mortar joints and the crown on a mild day, freezes overnight and expands, which is how cracks, loose bricks and leaks start. Nor'easters drive rain sideways into flashing and mortar that looked fine in summer. Most homeowners in Tamaqua, PA schedule a sweep in early fall, and a repair check after a hard winter.
A chimney problem fixed early rarely spreads to the masonry, the liner or the house.
Local sweeps see the same chimney types and weather wear across Tamaqua and nearby towns.
Ask the sweep about the cause, the options and the estimate before work starts.
More questions? Call (272) 291-2023
Restoring a damaged chimney liner so smoke and gases stay sealed inside the flue.
Learn moreA level 1, 2 or 3 review of the full chimney system so you know whether it is safe to light a fire.
Learn moreInsert installation for drafty, inefficient open fireplaces, with the chimney inspected before anything goes in.
Learn moreWood stove installation into an existing chimney or a new insulated chimney, so the stove drafts well and stays clear of anything that can burn.
Learn moreLooking for something else?
See all chimney servicesCall now for Tamaqua chimney liner installation and help in the towns around it.
Free to call. No forms to fill out.